AAON LZ Series Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 104

AAON LZ Series Скачать руководство пользователя страница 103

Literature Change History

July 2015

Initial version.

August 2016

Added a warning to empty the evaporative-condensed chiller condenser tank before lifting.
Included the size for the makeup water connection. Changed e-coated condenser coil cleaning to
100 psi.

January 2017

Added vestibule exhaust fan section.

October 2017

Added figure to show LZ bases. Added end flashing installation section. Added 3 phase
imbalance discussion. Added frequency ranges for VFD compressors. Added a note that reverse
osmosis and deionized water cannot be used in the evaporative cooled condensing units. Added
suction line filter removal instructions.

May 2018

Updated technical support contact information.

June 2018

Updated E-coated coil cleaning procedure. Updated Flo-Trex Combination Valve section.
Minor Revision changed to “A” because LZ is now AHRI certified. Changed terminology from
Evaporative-Cooled Condenser to Evaporative-Condensed Chiller.

March 2019

Added low sound ECM condenser fan option in the nomenclature section. Added temporary
drain instructions. Added sump level. Added instructions for leak checking evaporative-
condenser section access doors.

May 2019

Added the minimum/maximum voltage range table in the Electrical section.

«
...
101
102
103
104
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды