AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 78 / 104

background image

78

significantly  less  than  the  nameplate  head
value it is typically permissible to throttle the
discharge  isolation  valve  until  the  actual
operating  head  is  equal  to  the  nameplate
value.

Any  noise  or  vibration  usually  disappears.
The  system  designer  or  operator  should  be
made aware of this soon as some adjustment
may  be  required  to  the  pump  impeller
diameter  or  drive  settings,  if  applicable,  to
make  the  pump  suitable  for  the  system  as
installed.

Check  rotation  arrow  prior  to  operating  the
unit. The rotation of all Vertical In-Line units
is  “clockwise” when viewed from  the drive
end.  (Looking  from  on  top  of  /  behind  the
motor)

General Care

Vertical  In-Line  pumps  are  built  to  operate
without  periodic  maintenance,  other  than
motor  lubrication  on  larger  units.  A
systematic  inspection  made  at  regular
intervals,  will  ensure  years  of  trouble-free
operation,  giving  special  attention  to  the
following:



Keep unit clean



Keep moisture, refuse, dust or other loose
particles away from the pump and
ventilating openings of the motor.



Avoid operating the unit in overheated
surroundings (Above 100ºF/40ºC).

Any  possibility  of  the  unit  starting  while
being serviced must be eliminated.

If mechanical seal environmental accessories
are installed, ensure water is flowing through
the  sight  flow  indicator  and  that  filter
cartridges are replaced as recommended.

Lubrication

Pump

Lubrication  is  not  required.  There  are  no
bearings  in  the  pump  that  need  external
lubrication service.

Large Series split-coupled units are installed
with  a  shaft  bushing  located  beneath  the
impeller  that  is  lubricated  from  the  pump
discharge. This bearing is field removable for
service  on  the  20x20x19  size  without
disturbing  the  motor  or  other  major  pump
components.

Motor

Follow

the

lubrication

procedures

recommended  by  the  motor  manufacturer.
Many  small  and  medium  sized  motors  are
permanently  lubricated  and  need  no  added
lubrication.  Generally  if  there  are  grease
fittings  evident  the  motor  needs  periodic
lubrication, and if there are no grease fittings
evident, no periodic lubrication is required.

Check  the  lubrication  instructions  supplied
with  the  motor  for  the  particular  frame  size
indicated on the motor nameplate.

Check

rotation

arrow

prior

to

operating the unit.

CAUTION

Electric

shock

hazard.

Before

attempting to perform any service or
maintenance

on

pumping

unit,

disconnect power source to the driver,
LOCK IT OFF and tag with the reason.

WARNING

«
...
76
77
78
79
80
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: Yard-Man Страницы: 20

ECOWISE RTAF HE

Бренд: Trane Страницы: 124

Бренд: Cobra Страницы: 11

Бренд: Traulsen Страницы: 26

Бренд: Elkay Страницы: 2

Бренд: Delta Страницы: 6

Hyperchill ICE076

Бренд: Parker Hiross Страницы: 172

Бренд: McCulloch Страницы: 44

Бренд: Go-On Страницы: 28

Бренд: YARDMAX Страницы: 24

Бренд: York Страницы: 188

Бренд: Parkside Страницы: 268

Бренд: Koolatron Страницы: 2

Бренд: Robur Страницы: 80

Бренд: Aqua Logic Страницы: 4

Бренд: S&A Страницы: 11

Бренд: Ecoboil Страницы: 4

Бренд: Tecumseh Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды