AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 43 / 104

background image

43

Startup  technician  must  check  for  proper
motor  rotation  for  compressors,  condenser
fan motors, and pumps and check fan motor
amperage  listed  on  the  motor  nameplate  is
not exceeded. Motor overload protection may
be a function of the variable frequency drive
and  must  not  be  bypassed.    Variable
frequency  drives  are  programmed  to
automatically  rotate  the  fan  in  the  correct
rotation.    Do  not  rely  on  fan  with  variable
frequency drives for compressor rotation.

Note:

All units are factory wired for

208/230V, 460V, or 575V. If unit is to be
connected to a 208V supply, the transformer
must be rewired to 208V service.

Wire control signals to the unit’s low voltage
terminal  block  located  in  the  controls
compartment.

If  any  factory  installed  wiring  must  be
replaced, use a minimum 221°F (105°C) type
AWM insulated conductors.

Supply voltage must be within the min/max
range shown on the unit nameplate. Available
short  circuit  current  should  not  exceed  the
short circuit current rating (SCCR) shown on
the unit nameplate.

CONVENIENCE OUTLETS AND

SERVICE LIGHTS

Convenience  outlet  and  service  light
circuits  are  wired  to  the  incoming
power side of the disconnect.  These
circuits  will  remain  powered  even
when unit disconnect is off.

WARNING

Installing Contractor is responsible for
proper sealing of the electrical and
gas entries into the unit. Failure to seal
the entries may result in damage to
the unit and property.

CAUTION

Scroll  compressors  are  directional
and  will  be  damaged  by  operation  in
the  wrong  direction.  High  pressure
switches  on  compressors  have  been
disconnected  after  factory  testing.
Rotation  should  be  checked  by  a
qualified service technician at startup
using suction and discharge pressure
gauges  and  any  wiring  alteration
should only be made at the unit power
connection.

CAUTION

BURNING  FOAM  INSULATION  IS
TOXIC!    Do  not  cut  holes  into  any
foam insulated panels with any flame
producing  cutter  such  as  a  plasma
cutter or cutting torch.

WARNING

Three phase voltage imbalance will
cause

motor

overheating

and

premature failure.

CAUTION

«
...
41
42
43
44
45
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: Farmi Forest Страницы: 44

Бренд: Whirlpool Страницы: 56

Бренд: Cobra Страницы: 19

Бренд: EarthQuake Страницы: 11

JOLLY TOP 3V-VM

Бренд: Ferroli Страницы: 21

Catros 4001-2TS

Бренд: Amazone Страницы: 90

Бренд: AAON Страницы: 64

Бренд: Fulgor Milano Страницы: 192

30RAN010-055 AquaSnap

Бренд: Sterlco Страницы: 28

Бренд: Harbour Страницы: 2

Бренд: Yard Machines Страницы: 20

Бренд: KDF Страницы: 2

Бренд: EarthWay Страницы: 4

Бренд: Raider Страницы: 114

Бренд: Simplicity Страницы: 40

Бренд: Quantech Страницы: 188

Бренд: Gastrodomus Страницы: 47

OPTIVIEW YD Series

Бренд: York Страницы: 160

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды