AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 89 / 104

background image

89

7.

Close the system-isolating valve.

8.

Open suction isolating valve.

9.

Switch on unit, initially both pumps will
run. As the pressure reaches the pump
control switch threshold, the pumps will
switch off.

10.

Check all piping for leaks following
shipping.

11.

Crack open system valve. The pressure
will fall and the pump will start and
maintain pressure.

Powered agitation (Ultra model only):

A solenoid valve is fitted to provide powered
agitation  of  the  mixture.  Automatically  this
valve  is  periodically  opened  and  the  duty
pump  starts  creating  circulation  through  the
pump and mixing tank. Automatic mixing is
inhibited when there is a system demand for
makeup.
A  switch  is  provided  for  manual  agitation
when adding glycol to the mixing tank.

Topping up with glycol:

The mixing tank is calibrated in liters and US
gallons. The normal top up level is 53 US
gallons (200 liters).
1.

Calculate the amount of water needed and
add or drain to the correct level.

2.

Add the required amount of glycol.

3.

Operate the manual-agitating switch.

4.

Check the mixture percentage.

The unit is now ready for service.

Flo-Trex Combination Valve

Introduction

The  Flo-Trex  combination  valves  are
designed for installation on the discharge side
of  centrifugal  pumps,  and  incorporate  three
functions in one valve:

1.

Drip-tight shut-off valve

2.

Spring closure design, Non-slam check
valve

3.

Flow throttling valve

Armgrip Flange Adapter Installation

1.

Position  the  two  halves  of  the  Armgrip
flange adapter on the valve body ensuring
that  the  lugs  on  each  half  of  the  flange
adapters  are  located  between  the  anti-
rotation  lugs  on  the  valve  body  (as
shown).

Insert two bolts of specified size (Table A1)
to secure the halves of the flange adapter to
the valve body (as shown).

«
...
87
88
89
90
91
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: York Страницы: 184

Бренд: Gardeo Страницы: 43

Бренд: Hitachi Страницы: 140

Бренд: Texas Страницы: 60

Бренд: GreenWorks Tools Страницы: 175

Бренд: Troy-Bilt Страницы: 32

Бренд: Troy-Bilt Страницы: 36

Бренд: Hyundai Страницы: 20

Бренд: Tracmaster Страницы: 2

Бренд: Salsco Страницы: 41

Бренд: Echo Страницы: 48

R-407C Optimized

Бренд: York Страницы: 120

Бренд: Daikin Страницы: 143

Бренд: Craftsman Страницы: 36

Бренд: York Страницы: 28

Бренд: York Страницы: 32

Бренд: AIREDALE Страницы: 63

Бренд: Vermeer Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды