AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 11 / 104

background image

11

1.

Startup and service must be performed by
a Factory Trained Service Technician.

2.

The unit is for outdoor use only. See
General Information section for more
information.

3.

Use only with type of the gas approved
for the boiler. Refer to the boiler rating
plate.

4.

Provide adequate combustion ventilation
air to the boiler.

5.

Every  unit  has  a  unique  equipment
nameplate  with  electrical,  operational,
and unit clearance specifications. Always
refer  to  the  unit  nameplate  for  ratings
unique to the model you have purchased.

6.

READ THE ENTIRE INSTALLATION,
OPERATION AND MAINTENANCE
MANUAL.

OTHER

IMPORTANT

SAFETY

PRECAUTIONS

ARE

PROVIDED THROUGHOUT THIS
MANUAL.

7.

Keep this manual and all literature
safeguarded near or on the unit.

Polyolester (POE) and Polyvinylether
(PVE) oils are two types of lubricants
used  with  R-410A  and  R134a
refrigeration  systems.  Refer  to  the
compressor  label  for  the  proper
compressor lubricant type.

CAUTION

Do not clean DX refrigerant coils with
hot water or steam. The use of hot
water or steam on refrigerant coils will
cause high pressure inside the coil
tubing and damage to the coil.

CAUTION

Rotation must be checked on ALL
MOTORS AND COMPRESSORS of 3
phase units at startup by a qualified
service

technician.

Scroll

compressors  are  directional  and  can
be  damaged  if  rotated  in  the  wrong
direction.  Compressor  rotation  must
be  checked  using  suction  and
discharge gauges. Fan motor rotation
should

be

checked

for

proper

operation. Alterations should only be
made at the unit power connection.

CAUTION

Some

chemical

coil

cleaning

compounds are caustic or toxic. Use
these substances only in accordance
with

the

manufacturer

’s

usage

instructions.

Failure

to

follow

instructions may result in equipment
damage, injury or death.

WARNING

«
...
9
10
11
12
13
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: Lorenz Страницы: 30

Бренд: HIdRos Страницы: 76

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 33

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 33

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды