AAON LZ Series Скачать руководство пользователя | Manualshive

Страница: 92 / 104

background image

92

Flow Measurement with the valve in the
throttled position

Step 1.

The valve stem with its grooved rings

and positioning sleeve indicates the throttled
position of the valve.

The quarter turn graduations on the sleeve,
with the scribed line on the stem provide an
approximate flow measurement.

Note: The valve is shipped in closed
position. The indicator on the plastic sleeve
is aligned with the vertical scribed line on
the stem.

Step 2.

Record the size of the valve and stem

position using the flow indicator scale.
Calculate the percentage of valve opening
based on the number of rings at the fully open
position.

Valve Size

2-1/2

3 4 5 6

8

10

12

Number of

Rings

5

5 6 9 10 12 18

28

(valve

fully open)

Step 3.

Measure and record the differential

pressure across the valve in the throttled
position.

Step 4.

Locate percentage of valve opening

on the bottom scale of Inherent Flow
Characteristic Curve with Valve in Throttled
Position. Project line vertically up to intersect
with the Valve Characteristic Curve and from
this point project line horizontally across to
the left of the chart and record the percentage
of maximum flow rate.

«
...
90
91
92
93
94
...
»

Содержание LZ Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для LZ Series

Бренд: Zanotti Страницы: 72

Бренд: Cleveland Страницы: 18

Бренд: Daikin Страницы: 34

Бренд: Salsco Страницы: 40

Бренд: York Страницы: 226

Бренд: Welbilt Страницы: 42

Бренд: Westfalia Страницы: 40

Бренд: Tiller Joe Страницы: 16

Бренд: AIREDALE Страницы: 46

Ultima Compact UCCL030-75 1 FAN

Бренд: AIREDALE Страницы: 62

Бренд: Cub Cadet Страницы: 24

Бренд: Cub Cadet Страницы: 40

COOL CABI OCA-H300BC-AW2

Бренд: OHM ELECTRIC Страницы: 88

MILLENNIUM YCAR0315

Бренд: York Страницы: 160

Бренд: York Страницы: 72

Бренд: Craftsman Страницы: 25

ActiveCore SKT series

Бренд: Skope Страницы: 82

Бренд: Daikin Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды