3DHISTECH P1000 Скачать руководство пользователя страница 91

Страница: 91 / 94

P1000 SERVICE SOFTWARE MANUAL

15. SLIDE PREVIEW UNIT

SERVICE GUIDE

Adjusting the unit

1.1.

Initialize the unit.

1.2.

Select the sample area at the

Grab image

section, then click the

Live view

button.

1.3.

Click the

Slide to preview grab pos

button to move the labeled slide under the camera.

1.4.

Click

Focus position Y

, position the Arm so that the sample area fills out most of the selection area.

Caution!

Make sure that the slide is not moved further than the line! Click

Save

to save the Y coordinate value!

1.5.

Click

Preview grab pos

, and if the slide is positioned correctly at the previous step, the coordinate value must be saved here as well.

1.6.

Click the

Live view

button to stop live image recording, click

Label/barcode area

button and click

Live image recording

button again. Now,

the barcode area is visible between the marker/border lines.

1.7.

Click the

Barcode grab pos

button. Move the Arm in Z-direction until the slide edge near the Arm is positioned within the selection area. Save

the coordinates.

1.8.

Click the

button to load back the slide.

Note!

The slide can be loaded back to the magazine only if live image is not recorded, otherwise this button is inactive!

Содержание P1000































































































Результаты поиска

Содержание P1000

Отзывы:

Бренды по названию

Популярные бренды

3DHISTECH P1000, Руководство по обслуживанию

Результаты поиска

Содержание P1000

Отзывы:

Бренды по названию

Популярные бренды