3DHISTECH P1000 Скачать руководство пользователя

Страница: 14 / 94

P1000 SERVICE SOFTWARE MANUAL

6. SENSORS

SERVICE GUIDE

After initialization, click the

Validation/Testing

button. As

Turn on/off

sensors

does not work currently, activate sensors according to the description

below.

After validation, click the

Step motors

and then, the

Turn on/off

sensors

button

in the

Validation/Sensors

activates. As a result, the

sensors can be controlled manually.

Slide edge

4.1.

After turning on the sensor, the electronics on the Arm is activated.

4.2.

The operation of the sensor can be validated blocking the laser beam by hand
and moving it near. As a result, the displayed value must be changing. Tuning
of the sensor is described later.

Slide out

5.1.

After turning on, the operation led lights up.

5.2.

There are three states of the led: prism on, prism off, uncertain. Tuning of the
sensor is described later.

Handle the laser

sensors with

extra attention!

Prism on

Prism off

Uncertain

Содержание P1000































































































Результаты поиска

Содержание P1000

Отзывы:

Похожие инструкции для P1000

Бренды по названию

Популярные бренды

3DHISTECH P1000, Руководство по обслуживанию

Результаты поиска

Содержание P1000

Отзывы:

Похожие инструкции для P1000

Бренды по названию

Популярные бренды