manualshive.com logo in svg

3DHISTECH P1000, Руководство по обслуживанию

Поделиться
Скачать
3DHISTECH P1000 Скачать руководство пользователя страница 31

P1000 SERVICE SOFTWARE MANUAL 

10. ND FILTER 

 

 

 

30 

SERVICE GUIDE 

 

3.

 

The high-

level setup window is the same as the aperture’s. Create three positions and select position one (filtered position).

 

 

4.

 

Click the 

Slice motor position

 button to activate the motor control panel. Click the 

Home

 button. 

 

5.

 

Step the disk in positive direction until the filter and the objective behind are aligned (you can light the unit with a lamp from the direction of the 
condenser). When done, click 

 on the side panel to set this value and to the 

Slice motor position

 cell. 

 

6.

 

Repeat steps from 10.3 to 10.5 to find the other two filter positions. Click 

 to set the values. 

 

7.

 

After defining all three values, start the validation process. Set 

Test count

 to the intended value or set 1 and validate the component. 

 

 

 

 

Содержание P1000































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды