3DHISTECH P1000 Скачать руководство пользователя страница 9

Страница: 9 / 94

P1000 SERVICE SOFTWARE MANUAL

4. USER INTERFACES AND FUNCTIONALITIES OF MOTOR/COMPONENT CONTROL

PANELS

SERVICE GUIDE

4. User Interfaces and Functionalities of Motor/Component Control Panels

Name of

motor/component

Stepping unit, the distance the motor covers by

one click (0,01-100.000).

For security reasons, start with the lowest value

stepping up gradually.

Positive, negative

navigation

by the defined

step values

Caution!

The arrows do not

necessarily show the

direction of physical

movement!

Go to II

Navigates the

motor/component to the

position defined by the

Aperture motor position

value. (0.85µm in this

case).

Home

: Finds the motor

zero position.

Finds (if applicable):

1. Magnet of Hall sensor
motors

2. Zero sign of metric gauge
3. Home position value of
absolute metric gauge

Set value

Writes the Pos field value

to Aperture motor

position field.

Go to I

Navigates the motor/

component to the

position defined in Pos

field.

The

Pos field

has double

functionality: displays

current position after

navigation or target

position can be defined.

IGURE

IDE

ANEL AND

PERTURE

IGH

EVEL

ETUP

[FF3] megjegyzést írt:

Home fülön a tördelés nem az

igazi a 3 pontnál

Содержание P1000































































































Результаты поиска

Содержание P1000

Отзывы:

Бренды по названию

Популярные бренды

3DHISTECH P1000, Руководство по обслуживанию

Результаты поиска

Содержание P1000

Отзывы:

Бренды по названию

Популярные бренды