manualshive.com logo in svg

3DHISTECH P1000, Руководство по обслуживанию

Поделиться
Скачать
3DHISTECH P1000 Скачать руководство пользователя страница 22

P1000 SERVICE SOFTWARE MANUAL 

7. STEP MOTORS 

 

 

 

SERVICE GUIDE 

21

 

 

5.3.

 

Click the 

Start motor

 button. Then the unit moves a little, which is not always visible. 

 

5.4.

 

Select the smallest step unit at 

Motor limit

. 

Set a step value at

 

Motor movement

 to move the motor. 

 

 

Caution!

 

If you are unsure, set low values and reach the desired position gradually. Setting 1000 steps is normally OK for most motors.

 

 
5.5.

 

Clicking the 

Motor movement

 plus and minus buttons, navigate the unit to the intended position. 

 

5.6.

 

Save this position clicking the 

Set test start position

 button. The software will start the step test from here. 

 

5.7.

 

Define the movement coordinates adjusting the 

Test movement

 

slide (for example, +500 steps). 

 

5.8.

 

Clicking the 

Test

 

button,

 

the unit will move +500 steps from the test start position and then -500 steps back. 

 

6.

 

Click the

 

Start motor

 button to wake P1000 up and click 

Test motor

. If the units are correctly set, a green tick appears in the related boxes. The 

Validate

 button only activates if all motors have passed the test. 

 

7.

 

Validate the results and save. 

 

 

 

 

Содержание P1000































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды