3DHISTECH P1000 Скачать руководство пользователя страница 71

Страница: 71 / 94

P1000 SERVICE SOFTWARE MANUAL

14. SLIDE LOADING UNITS

SERVICE GUIDE

As soon as the height is set, save the coordinates. After saving, the

Slide operations

buttons are activated, and the adjusted magazine is marked

green.

Click the

Slide out

button. If you hear a friction sound, the settings are incorrect! Re-insert the slide without friction and stalling! When the

insertion to the first position is done, set the slider to position 19. Click

Approach the slide

then click the

Slide out and back

button. No friction

and stalling are allowed. However, if there is friction or stalling, fine tune the

Top slide position

In case of a successful adjustment, continue to

set all impacted magazines accordingly.

It is recommended to save each column after setting!!

Select

Preview position

in the

Setup selection

menu.

Caution!

The preview image display may be slightly distorted!

Slide out

Slide back

Slide out and back

Remove slide manually

Содержание P1000































































































Результаты поиска

Содержание P1000

Отзывы:

Бренды по названию

Популярные бренды

3DHISTECH P1000, Руководство по обслуживанию

Результаты поиска

Содержание P1000

Отзывы:

Бренды по названию

Популярные бренды