Zte ZXDSL 9210 (V3.1) Technical Manual Download Page 106

Page: 106 / 182

ZXDSL 9210 (V3.1) Broadband Universal Access Equipment Technical Manual

5-20

5.6.2 Bearer Subsystem

The structure of the bearer subsystem is shown in Fig. 5.6-1.

Control part

Forwarding part

Forwarding engine

submodule

Routing engine

submodule

Statistics engine

submodule

Connection control module

Line interface

I ch
an

Fig. 5.6-1 Structure of Bearer Subsystem

In the architecture of ZXDSL 9210, the bearer master control module is on the

embedded BAS. Connection-related modules are on the SCBF, and are implemented in

the form of microcodes. The bearer subsystem is responsible for the following

functions:

1. Judgment of the encapsulation and type of input packets.

2. Encapsulation of output packet according to the NNI interface type.

3. Routing for packets and forwarding.

4. Setup, maintenance and release of data connections and control connections.

5. Maintenance of part of the MIB information.

6. Provides user bandwidth control.

Summary of Contents for ZXDSL 9210 (V3.1)























































































































































































Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands

Zte ZXDSL 9210 (V3.1), Technical Manual

Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands