Zte ZXDSL 9210 (V3.1) Technical Manual Download Page 158

Page: 158 / 182

ZXDSL 9210 (V3.1) Broadband Universal Access Equipment Technical Manual

8-4

8.1.3 Convergence of Multiple 9210 Devices

The BAS is generally located at the convergence layer. When several ZXDSL 9210

devices are accessed to the BAS, convergence is required for access to the BAS.

Normally, Layer 2 switching equipment is used to provide convergence. The

networking diagrams of ADSL, VDSL, and Ethernet user access are similar to each

other, therefore ADSL or VDSL user access networking is taken for example. As

shown in Fig. 8.1-5, the equipment is connected uplink with a BAS (ZTE UAS2500 or

UAS5000 can be used).

Router

Splitter

9210

Splitter

9210

Splitter

Phone

Splitter

Phone

9210

MODEM

9210

Network service

provider

Twisted

pair

Twisted

pair

PSTN switch

Subscribe premises

equipment

ZXDSL

Support VLAN

Layer 2

equipment

Fig. 8.1-5 Networking Diagram when Multiple 9210s are Converged

The Layer 2 switch for ZXDSL 9210 convergence must support VLAN. The ZXDSL

9210 devices must be isolated by different VLANs. If a Layer 2 device is connected

with other subscribers at the same time, VLAN isolation is also required.

Summary of Contents for ZXDSL 9210 (V3.1)























































































































































































Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands

Zte ZXDSL 9210 (V3.1), Technical Manual

Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands