Zte ZXDSL 9210 (V3.1) Technical Manual Download Page 105

Page: 105 / 182

Chapter

Erro! Estilo não definido.

5-19

8. L2TP submodule: Supports LAC and LNS.

9. AAA submodule: Provides support for the AAA.

10. Routing submodule: Used to update global forwarding tables and local

forwarding tables, and provide update interfaces and maintenance interfaces for

forwarding tables.

11. Multicast submodule: Supports IGMP Proxy protocol and IP multicast.

12. FTP protocol submodule: Adopts the RouterWare protocol stack to implement

remote version load.

13. Unicast routing module: The unicast routing table maintenance module is

responsible for addition, deletion, and finding of routing tables. The unicast

dynamic routing protocol module generates unicast routing tables. The route

forwarding table maintenance module implements hardware forwarding routes.

14. VBAS module: By modifying authentication process, BAS queries users’

physical location from the central office equipment before BAS begins

authentication, and takes this value as the basis for physical locating and

authentication of users.

Summary of Contents for ZXDSL 9210 (V3.1)























































































































































































Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands

Zte ZXDSL 9210 (V3.1), Technical Manual

Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands