Zte ZXDSL 9210 (V3.1) Technical Manual Download Page 174

Page: 174 / 182

ZXDSL 9210 (V3.1) Broadband Universal Access Equipment Technical Manual

B-4

Standard No.

Standard Name

IEEE 802.3x

Full Duplex and Flow control on 10BaseT and 100BaseT ports.

IEEE 802.3u,

100BaseTX and 100BaseFX specification.

IEEE 802.3z

1000BaseX specification.

B.4 National Standards

Table B.4-1 National Standards

Standard No.

Standard Name

GIB/Z35-93

Components Derating Criteria

GJB 450-88

General Syllabus for Reliability of Equipment Development & Manufacture

GJB/299A-91 Electronic

Equipment

Reliability Estimation Manual

YD/T 282-2000

Universal Test Methods of Communication Equipment Reliability

GJB 299B

Electronic Equipment Reliability Estimation Standards

GJB 367.5-87

Technical Condition Standards for Universal Military Equipment, including Requirements

for Packing, Transportation and Storage

GB/T13426-92

Reliability Requirements and Experimental Standards for Digital Communication

Equipment

GB 5080-86

General Experimental Requirements for Equipment Reliability and Guidelines for

Experimental Period Design

GB/T 2423

Experimental Procedures for Basic Environment of Electrical and Electronic Products

GB 191-2000

Graphical Marks for Packing, Storage and Transportation (eqv ISO 780:1997)

GB 2828-87

Batch-by-Batch Check Count Sample Program and Sample Table (Applicable to

Continuous Batch Check)

GB 2829-87

Periodical Check Count Sample Program and Sample Table (Applicable to Check of

Production Stability)

GJB 299B

Electronic Equipment Reliability Estimation Standards

GJB 367.5-87

Technical Condition Standards for Universal Military Equipment, including Requirements

for Packing, Transportation and Storage

GB/T 14733

1995

Telecom Terms

GB/T 6388-1986

Marks for Transportation, Packing, Delivery, and Receiving

GB/T 17626.2 -1998

Electromagnetic Compatibility Experiments and Measurement Technologies Static

Discharge Noise Immunity Experiments (idt IEC 61000-4-2:1995)

GB/T 17626.3 -1998

Electromagnetic Compatibility Experiments and Measurement Technologies RF

Electromagnetic Radiation Noise Immunity Experiments (idt IEC 61000-4-3:1995)

GB/T 17626.4 -1998

Electromagnetic Compatibility Experiments and Measurement Technologies Electrical

Fast Transient Pulse Group Noise Immunity Experiments (idt IEC 61000-4-4:1995)

GB/T 17626.5 -1998

Electromagnetic Compatibility Experiments and Measurement Technologies Surge

Summary of Contents for ZXDSL 9210 (V3.1)























































































































































































Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands

Zte ZXDSL 9210 (V3.1), Technical Manual

Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands