Zte ZXDSL 9210 (V3.1) Technical Manual Download Page 63

Page: 63 / 182

4-1

4 Hardware Structure

This chapter introduces the hardware structure of the system, including the

single-frame configuration and integrated equipment configuration of the system.

Besides, it introduces the functions, principles, and interfaces of the system boards.

And this helps the user better understand the hardware structure of the system.

4.1 Overall Architecture of the System

The ZXDSL 9210 system adopts a 17U 2-layer frame structure. The upper-layer is a

splitter adopting a 7U board while the lower layer is the SCBF and user board which

adopt 9U standard boards. The lower layer is composed of two active/standby SCBFs,

15 line interface boards, Ethernet uplink boards, 1000M Ethernet optical interface

boards or embedded BASs. Ethernet uplink boards, 1000M Ethernet optical interface

boards and embedded BASs can be plugged together with line interface board slots.

Besides, the system adopts distributed power supply mode. The overall hardware

architecture of the ZXDSL 9210 system is shown in Fig. 4.1-1.

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

Line interface

board

ont
ro

l &

itc

ng boar

Fig. 4.1-1 Overall Hardware Architecture of the System

Summary of Contents for ZXDSL 9210 (V3.1)























































































































































































Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands

Zte ZXDSL 9210 (V3.1), Technical Manual

Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands