Zte ZXDSL 9210 (V3.1) Technical Manual Download Page 96

Page: 96 / 182

ZXDSL 9210 (V3.1) Broadband Universal Access Equipment Technical Manual

5-10

board is powered on, the kennel program in BootRom will be first run to call an

application program version. During the system running, users may download a

new version by means of remote NM requests. Any new version will be

downloaded to the SCBF and sent via the HDLC link to the line interface board.

During the system initialization, this module checks the version numbers of

application programs run on all the line interface boards currently started. If

there is any inconsistency, alarms will be generated and reported to the NMS.

5. Embedded BAS (RPCK) interface module

The embedded BAS (RPCK) interface module is used for MAC address

translation of IP packets sent from the SCBF to RPCK. Besides, this module

sends these packets to the port where RPCK is located. This module is also

responsible for MAC address translation of IP packets received from RPCK and

sends it to the agent process via the IP layer. The agent process forwards the NM

information to users’ NM interfaces to enable users to perform NM operations of

RPCK in the NM of the main set.

5.4.4 Database Subsystem

The database subsystem is composed of database modules only. The database modules

here are not in a common sense. Various object data in the whole system are distributed

in respective modules, which maintain corresponding data. The system provides a

unified framework so that various modules gain unified access to distributed object

data. This framework provides the interfaces necessary for this access. Thus, SNMP

agent gains access to various MIBs by means of this framework.

5.4.5 L3/4 Protocol Subsystem

The L3/4 protocol subsystem consists of TCP/IP protocol modules. This subsystem

implements TCP, UDP, ICMP, IP, ARP, and RARP.

The whole L3/4 protocol subsystem runs on the SCBF. All data information input are

sent via inband line interface board or outband to the switching chip on the SCBF. This

chip sends the information to the CPU on the SCBF. The output of the data information

led in via inband line interface board is sent inband by the switching chip on the SCBF

and the output of data information led in via outband line interface board is sent

outband.

Summary of Contents for ZXDSL 9210 (V3.1)























































































































































































Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands

Zte ZXDSL 9210 (V3.1), Technical Manual

Search results

Summary of Contents for ZXDSL 9210 (V3.1)

Reviews:

Related manuals for ZXDSL 9210 (V3.1)

Brands by name

Popular brands