Zte ZXA10 C300 Configuration Manual Download Page 234

Page: 234 / 301

ZXA10 C300 Configuration Manual (CLI)

ZXAN(config-ces-pw)# psn mpls-staticdouble 0x1b68 0xff9e8 0x1b67 0xff9e7 dst-mac

0015.eb72.0003 vlan 1000 priority 7

Save the configuration data.

ZXAN(config-ces-pw)# end

ZXAN# write

Result

The TDM relay service is successfully configured on both C300s and F829s.

16.5 PW Redundancy Configuration

16.5.1 Configuring the VPLS Redundancy

VPLS redundancy enhances the stability and reliability of MPLS network.

Networking Diagram

Figure 16-24

shows the networking diagram of the VPLS redundancy.

Figure 16-24 Networking Diagram of VPLS Redundancy

The PW redundancy group works in either 1:1 or 1+1 mode.

In 1:1 mode, only the active PW forwards the user traffic.

In 1+1 mode, both PWs forward the user traffic.

The network supports the

OSPF

and

LDP

protocols.

Configuration Data

Table 16-12

lists the configuration data of the VPLS redundancy.

16-78

SJ-20130520164529-007|2013-06-30 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXA10 C300














































































































































































































































































































Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands

Zte ZXA10 C300, Configuration Manual

Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands