Zte ZXA10 C300 Configuration Manual Download Page 196

Page: 196 / 301

ZXA10 C300 Configuration Manual (CLI)

Figure 16-13 HPVLS Networking Diagram

ONU

1, ONU2, and ONU3 are in the same VPLS network. ONU1 and ONU2 are connected

to the VPLS network through the User-facing

(UPE), while ONU3 is connected to the

VPLS through the PE. The Network PE (NPE) communicates with the UPE through a

spoke

sessions.

Configuration Data

Table 16-7

lists the configuration data of the HVPLS.

Table 16-7 HVPLS Configuration Data

Item

Data

Loopback interface

ID: 1

IP address: 1.1.1.1/32

L3 interface

VLAN ID: 10

Interface: gei_1/21/1

IP address: 10.1.1.1/24

Reserved VPN VLAN

VLAN ID: 4090

Name: 2and1000pw

Mode: dynamic pwe3

Type: ethernet-vlan

Peer: 2.2.2.2

Router ID: 2.2.2.2

ID: 1000

C300-1

16-40

SJ-20130520164529-007|2013-06-30 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXA10 C300














































































































































































































































































































Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands

Zte ZXA10 C300, Configuration Manual

Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands