Zte ZXA10 C300 Configuration Manual Download Page 186

Page: 186 / 301

ZXA10 C300 Configuration Manual (CLI)

Result

Two ONUs can ping each other successfully.

16.2.2 Configuring the Full-Mesh VPLS

To connect all of the customer LANs, full mesh connectivity is required. LDP is used for

full mesh establishment for VPLS.

Networking Diagram

Figure 16-11

shows the networking diagram of the full-mesh VPLS.

Figure 16-11 Networking Diagram of Full-Mesh VPLS

ONU

1, ONU2, and ONU2 are in the same VPLS network. These three ONUs communicate

with each other through the

s based on the

LDP

sessions.

Configuration Data

Table 16-6

lists the configuration data of the full-mesh VPLS.

16-30

SJ-20130520164529-007|2013-06-30 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXA10 C300














































































































































































































































































































Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands

Zte ZXA10 C300, Configuration Manual

Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands