Zte ZXA10 C300 Configuration Manual Download Page 124

Page: 124 / 301

ZXA10 C300 Configuration Manual (CLI)

In LACP mode, multiple physical ports are dynamically aggregated into a trunk group

to form a logical port, thus to balance the load of the egress/ingress flow among

the member ports. Aggregation is automatically generated to obtain the maximum

bandwidth.

The ZXA10 C300 link aggregation function complies with the following rules:

The link aggregation function supports up to eight trunk groups, and each trunk group

contains up to eight member ports.

The inter-interface card aggregation is supported, and the member ports can be

located on any interface card.

Member ports must operate in full duplex mode, and the working rates and VLAN

attributes must be consistent.

The logical port formed by link aggregation on the ZXA10 C300 is called smartgroup.

Smartgroup has the same default VLAN attributes as a common Ethernet port.

Steps

In global configuration mode, create a smartgroup.

ZXAN(config)#interface smartgroup1

ZXAN(config-smartgroup1)#

Configure load balancing mode.

ZXAN(config-smartgroup1)#smartgroup load-balance src-dst-mac

Note:

The ZXA10 C300 supports six load balancing modes that are based on source

IP,

destination

IP,

source/destination

IPs,

source

MAC,

destination

MAC,

and source/destination MACs respectively.

The default mode is based on

source/destination MACs.

Configure LACP mode.

ZXAN(config-smartgroup1)#smartgroup mode 802.3ad

Note:

The ZXA10 C300 supports two LACP modes:

On: LACP static aggregation mode.

802.3ad: LACP dynamic negotiation mode

Configure the VLAN for the smartgroup.

ZXAN(config-smartgroup1)#switchport vlan 100 tag

12-2

SJ-20130520164529-007|2013-06-30 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXA10 C300














































































































































































































































































































Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands

Zte ZXA10 C300, Configuration Manual

Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands