ZOTYE JNJ6460BK Manual Download | Manualshive

Page: 138 / 294

background image

138

Driving Instructions

Electronic Parking EPB

Automatic parking

In auto mode, when the vehicle stops, switch the one-key start switch from "ON" to
"OFF", the electric parking will perform the parking operation. After the parking is
succeed, parking indicator light shall be turned on.

When the auto mode is on, the one-key start switch is in "ON" position and the
vehicle stops, open the main driving door, the electric parking assembly will perform
the parking action. After the parking is succeed, parking indicator light shall be
turned on.

Automatic release

The electronic parking assembly can differentiate how to perform the automatic
release function based on the current road gradient.

Auto mode ON, parking mode, close main drive door, fasten safety belt, start engine,
depress clutch pedal (manual) or brake pedal (automatic), push gear to forward or
reverse gear, release clutch pedal (manual) or brake pedal (automatic), depress the
accelerator pedal, the electronic parking assembly will perform the release action;
When the vehicle’s forward power is greater than its sliding force, the electronic
parking assembly will perform the release action. After the successful release, the
parking indicator light will go out. This is the normal operation of the ramp start.

Dynamic braking

When the speed is faster than 3 km / h, the electronic parking will be released, pull
and maintain the parking button up, the electronic parking system will brake slowly
until the vehicle stops; If the parking button is released before parking, the electronic
parking system will not brake the vehicle.

Parking due to faults

If the speed signal is faulty, and the one-key start switch is set to "ON" position, pull
up the parking button and maintain for more than 30 seconds. The electronic parking
system will brake the vehicle with a small parking brake force. After 30 seconds, it
will gradually increase the parking power until the parking is successful. If the
parking button is released before the parking beomes successful, the brake will be
released.

«
...
136
137
138
139
140
...
»

Summary of Contents for JNJ6460BK







































































































































































































































































































Reviews:

No comments

Related manuals for JNJ6460BK

Brand: Carcomm Pages: 2

Brand: Whispbar Pages: 14

Brand: Mercedes-Benz Pages: 54

Brand: STO N SHO Pages: 7

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

2005 P207 Explorer Sport Trac

Brand: Ford Pages: 540

BASIC TLL171231

Brand: Tellur Pages: 5

Brand: Meta System Pages: 22

2000 Oldsmobile Intrigue

Brand: Oldsmobile Pages: 348

Brand: Kia Pages: 58

Brand: Black+Decker Pages: 21

Brand: Beeper Pages: 20

Brand: Mitsubishi Pages: 367

OVER DRIVE PolyPRO 3 Car Cover

Brand: Classic Accessories Pages: 2

Brand: Ultraplast Pages: 5

Brand: Valeo Pages: 29

Brand: v.link Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands