ZOTYE JNJ6460BK Manual Download | Manualshive

Page: 114 / 294

background image

114

Internal Setting

Trunk

Alarm!

●

Do not exceed allowable load and allowable total mass. If the allowable

load or allowable total mass is exceeded, it may cause the change of driving
performance of the vehicle, and occurrence of traffic accident and damage to
the vehicle.
●

Do not left the vehicle with back door opened attended. Children may

enter into the trunk, and suffer the life risk if locked there when the back door
is closed inside! Do not carry any passenger in the trunk.
●

In order to prevent articles in the trunk being thrown up, the trunk cover

must be firmly fixed in corresponding hold-down grooves. If improper or
damaged trunk cover is used, articles in the trunk may cause injury to
passengers in case of braking or traffic accident.

Trunk cover

When there is any goods loaded in the trunk, please pull the trunk cover in position
and ensure the back end of which is in the hold-down grooves at two sides of the
trunk, as shown in the figure above.

«
...
112
113
114
115
116
...
»

Summary of Contents for JNJ6460BK







































































































































































































































































































Reviews:

No comments

Related manuals for JNJ6460BK

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 24

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Ford Pages: 12

Jumpy Miltispace

Brand: CITROËN Pages: 164

Brand: Directed Pages: 30

MAGICGRIP MGQDWD-CPO

Brand: Scosche Pages: 12

transit connect 2012

Brand: Ford Pages: 299

Brand: Metra Electronics Pages: 8

Quantum Wash'n'Wipe N30205

Brand: National Cycle Pages: 12

80-485-142401-RT

Brand: Classic Accessories Pages: 14

Brand: Ford Pages: 46

Brand: U.S. General Pages: 3

Brand: Mack Pages: 133

Brand: Rand McNally Pages: 60

Brand: Suzuki Pages: 190

Brand: Chrysler Pages: 6

Brand: DV8 Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands