ZOTYE JNJ6460BK Manual Download | Manualshive

Page: 247 / 294

background image

Practical tips

247

Car tools

Warning triangle

The truck tool is located under the spare tire cover in the trunk as shown above.
Truck tools include: Warning triangle, jack, jack-crank, wheel nut wrench, trailer
ring.

The jack is in the spare tire pool under the spare tire cover in the trunk. Turn the
jack anticlockwise to tighten it and then remove it. After use, please fully retract
the jack arm, place it in place, rotate clockwise and fix the jack.

When the vehicle cannot move due to faults during driving, you can open the
warning triangle bracket, erect, or place it in the proper position behind the
vehicle (different locations under different road conditions) to remind the vehicles
driving in the same direction to pay attention and avoid.

Descriptions

If you place the warning triangle, place it on the general road, 50 meters away (in
the coming direction of vehicles) from the vehicle; If you must park the vehicle on
the highway, place it 150 meters behind the vehicle.

Manipulation

Safety

Driving guidance

Operating guide

DIY

Technical data

Index

«
...
245
246
247
248
249
...
»

Summary of Contents for JNJ6460BK







































































































































































































































































































Reviews:

No comments

Related manuals for JNJ6460BK

Brand: JANE Pages: 6

Brand: Back View Pages: 168

Brand: Jeep Pages: 12

Brand: Jeep Pages: 6

Brand: Kargo Master Pages: 5

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: Buick Pages: 428

10-8002-C11670C

Brand: Saleen Pages: 17

DELTA DL FIX 209FP

Brand: Menabo Pages: 8

Brand: Harman Kardon Pages: 16

Brand: TATA Motors Pages: 184

PW-50C Civilian

Brand: B&G electronics Pages: 7

Brand: tams elektronik Pages: 19

Brand: Ranger design Pages: 24

Brand: Saturn Pages: 440

FABIA II TMB PS 035

Brand: Skoda Pages: 16

Brand: Butts of Bawtry Pages: 2

LineCast Auto FM

Brand: Belkin Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands