Home
/
ZOTYE
/
JNJ6460BK
/
Manual

ZOTYE JNJ6460BK, Manual

Share

Page: 106 / 294

ZOTYE JNJ6460BK Manual Download Page 106

106

Internal Setting

Front 12V outlet

Rear USB interface, 12V power socket

The front 12V power socket is located below the air conditioning control panel, as
shown in the figure above.

Notice!

●

The on-board power socket is the socket of 12V, and the power load on

the socket is not allowed to exceed 120W.
●

When the engine is closed, don't use the power socket for a long time, so

as to avoid excessive discharge of the storage battery, and affect the starting
of the vehicle.
●

Please use the plug matched with the socket so as not to damage the

socket.

The rear USB interface and 12V power socket are located below the rear exhaust
outlet. When used, press the edge of the cover plate forward, the cover plate
pops up automatically, and the USB interface is opened or power socket cover
can be used. When not in use, the edge of the cover plate can be pushed forward,
and the cover plate is jammed and closed.

«
...
104
105
106
107
108
...
»

Summary of Contents for JNJ6460BK







































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands