ZOTYE JNJ6460BK Manual Download | Manualshive

Page: 101 / 294

background image

Seat

0

101

Rear seat

Before turning the rear seat backrest forward, please adjust the position of the front
seat so as to avoid it to be damaged due to the rear seat backrest turned forward.

Press the unlock mechanism and unlock the backrest of the rear seat and turn it
forward completely. The space in the trunk can be expanded by turning the backrest
of rear seat forward.

When the rear seat backrest is turned back, turn the backrest until it is locked, and
then pull the rear seat backrest to check whether it is fixed well.

Alarm!

●

After the rear seat backrest is turned back, the safety belt and safety belt

lock must be located in the normal backing position.
●

The rear seat backrest must be firmly locked, so that there will be no

product slipping from the trunk into the carriage during the emergency
braking!
●

Please ensure that the rear seat backrest is properly locked so that the

safety belt can reliably perform its function.
●

Before turning the backrest of the rear seat back to the locked position,

the rear side safety belt must be placed at the edge of the inner trim panel of
the vehicle body to prevent the safety belt clamp from being between the back
seat backrest and the inner trim panel and thus, it is damaged.

Manipulation

Safety

Driving guidance

Operating guide

DIY

Technical data

Index

«
...
99
100
101
102
103
...
»

Summary of Contents for JNJ6460BK







































































































































































































































































































Reviews:

No comments

Related manuals for JNJ6460BK

Brand: Toyota Pages: 56

Brand: Code 3 Pages: 8

Brand: SnapPad Pages: 5

1973 Convertible

Brand: Volkswagen Pages: 80

Porsche 911 GT3 R

Brand: iRacing Pages: 25

Brand: Yescom Pages: 4

Brand: Z Automotive Pages: 16

MILSCO KIT# C746700

Brand: K&M Pages: 2

Brand: Car-Interface Pages: 25

2 Bike Carrier 977

Brand: Thule Pages: 6

Brand: Thule Pages: 12

Brand: Icom Pages: 20

BEDXTENDER HD MAX 74841-00A

Brand: AMP Research Pages: 9

Brand: Belkin Pages: 2

Brand: Xpresskit Pages: 18

Brand: Thule Pages: 3

Brand: ULTIMATE SPEED Pages: 34

Brand: Draw tite Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands