ZOTYE JNJ6460BK Manual Download | Manualshive

Page: 249 / 294

background image

Practical tips

249

Replace wiper blade

The front windshield wiper blade should be regularly checked for wear or breakage.
If you want to change the front windshield wiper, please follow the steps below:
1.

Press the button above the front windshield wiper blade, as shown above.

2.

Lift the wiper arm slightly and remove the wiper blade by moving the wiper

blade in the opposite direction of the wiper arm.
3.

The installation sequence of new wiper blade is opposite to the dismantle

sequence.

Alarm!

When the windshield wiper blade is damaged, worn or unable to fully clean
the windshield glass, the window wiper blade must be replaced. Avoid
affecting vision.

Notice!

●

Damaged or dirty windshield wipers may scratch the windshield.

●

Solvent-based cleaners, hard sponges, and other sharp-edged items can

damage the wiper blade's graphite coating.
●

Do not clean the window glass with fuel, nail polish remover, paint

thinner or similar liquid.

Manipulation

Safety

Driving guidance

Operating guide

DIY

Technical data

Index

«
...
247
248
249
250
251
...
»

Summary of Contents for JNJ6460BK







































































































































































































































































































Reviews:

No comments

Related manuals for JNJ6460BK

Brand: Pacbrake Pages: 9

Brand: Hama Pages: 2

Brand: Falcon Pages: 8

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: K&M Pages: 3

Brand: Camcar Pages: 2

Brand: Subaru Pages: 3

Brand: Nav TV Pages: 2

Brand: Harbor Freight Tools Pages: 12

Brand: Honda Pages: 3

Brand: Whispbar Pages: 15

Ferrari 360 Map Carbon Light

Brand: MAcarbon Pages: 4

Brand: Thule Pages: 2

Brand: Caltrend Pages: 2

Brand: Advanced ICE Pages: 4

Brand: Yakima Pages: 13

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands