![background image](http://html.mh-extra.com/html/zoje/zj1900dss/zj1900dss_manual_936875119.webp)
COMPUTER-CONTROLLED HIGH SPEED LOCKSTITCH BAR TACKING MACHINE
- 48 -
8
.
Replenishing the designated places with grease
When the sewing machine has been used for a certain number of times of sewing, error
code No. E221 is displayed on the operation panel at the time of turning ON the power. This
display informs the operator of the time of replenishing the designated places with oil. Be sure
to replenish the places with the oil below. Then call the memory switch No. 245 and set it to
"0" with the RESET key. Even after the display of the error No. E221, when the RESET key is
pressed, the error is released, and the sewing machine can be continuously used. Afterwards,
however, the error No. E221 is displayed every time the power is turned ON.
In addition, when the sewing machine is used further for a certain period of time after the
display of error No. E220, the error No. E221 is displayed and the sewing machine fails to
operate since the error cannot be released even when the RESET key is pressed.
When the error No. E221 is displayed, be sure to replenish the designated places below
with oil. Then start up the memory switch and set No. 245 to "0" with the RESET key.
⑴
.
Outflow the residual oil in gearbox
⑵
.
Lubricate the upper gearbox
After replenishing the places with oil, the error No. E220 or No. E221 is displayed again
unless the memory switch No. 245 is changed to "0".
Turn OFF the power before starting the work so as to prevent accidents
cause by abrupt start of the sewing machine.
1) Tilt the machine, remove the screws
①
and seal .
②
2) put back sewing machine, outflow the
residual oil in the gearbox.
3) tilt the machine again, put back the seals
and screws
, then put sewing
②
①
machine back to the position.
1)
2)
When through the oil window
①
, you can not
find oil outlet obviously, or it is without oil outlet,
you should add the oil into the wheel gear box.
Turn off the machine, you can take down the
screw
②
and the rubber washer
③
,when it is
without oil outlet, please add 100ml 10# white
oil; when it is not oil outlet obviously, please
add 50-70ml.Please install back
②
and
③
parts,
turn on the machine and check whether it is
happened to oil outlet or not.
1
2
3
Summary of Contents for ZJ1900DSS
