Zip Commercial HydroTap 86682 Installation And Operating Instructions Manual Download Page 13

Hydro Tap Installation and Operating Instructions - 86682 - March 2012 v1.05                                        Page 13 of 20

Blue Chilled Water Light

On all the time:  

This indicates that the temperature of the chilled water is within the 
usable temperature range.

Flashing slowly : 

This indicates that the chilled water is not at the right temperature. Wait 
up to 20 minutes. When the chilled water is at the right temperature, the 
light will stop flashing. Note: The Zip HydroTap is designed to dispense 
chilled water in the temperature range 5°C to 15°C for BC120/60+ or 
5°C  to  10°C  for  BC160/125+  and  BC200/175+  depending  on  settings.                                                                   

During heavy usage, the temperature can rise out of this range.                                                                                                                               

Red Boiling Water Light 

On all the time: 

This indicates that the boiling water is ready. 

Flashing slowly : 

This indicates that the boiling water is below usable temperature.

 

Filter light

Filter Change Light Off: 

This  indicates  the  filter  is  operating  within  its  normal  specified  lifespan.                                                                                                  

Filter Change Light Flashing slowly :

The light will flash slowly when the filter is due for replacement and the 
LCD will show “Filter Change”. Refer to  “Replacing the filter” section of 
this document. (see P16 & P17). 

Lever Operation

Boiling Water Lever (with safety disengaged)                                                                                 

Depressing the “Red” lever allows dispensing of Boiling water.                       
Pulling up the Red lever allows the tap to operate in a “no-touch” mode. 
Water will flow

 

from between 5 and 15 seconds (This is user adjustable). 

To reset, return the handle to the “Off” position and repeat the step. The 
lever has to be manually returned to the “Off” position.

Chilled Water Lever                                                                                  

Depressing the “Blue” lever allows dispensing of Chilled water.                        
Pulling up the Blue lever allows the tap to operate in a “no-touch” 
mode. Water will flow from between 5 and 15 seconds (This is user 
adjustable). To reset, return the handle to the “Off” position and repeat 
the step. The lever has to be manually returned to the “Off” position.

 Operating the Tap

Note:

 On the Boiling only models the Chilled 

LED is blank.

Boiling

Chilled

Filter Change

Press or pull lever

Summary of Contents for Commercial HydroTap 86682





















Reviews: