ZIEHL-ABEGG FXD32AM Operating Instructions Manual Download Page 52 | Manualshive

Page: 52 / 123

background image

6.01

Air velocity control, Setpoint in m/s

Main menu

Setting

Start
Setting
Protocol
Base setup
Controller Setup

Base setup

Setpoint1

Setting range: in measuring range of sensor
Factory setting: 0.50 m/s

0.50 m/s

Setpoint1

Base setup

Setpoint2

Setting

“

Setpoint 2

”

e.g. reduced value for night operation.

Switch over Setpoint 1/2 by external contact (display as long as no allocation is carried
out:

|

- - - - -

|

IO Setup).

- - - - -

Setpoint2

Base setup

Pband

Narrow control range = Short control times
Wide control range = Longer control times and more stable control
Setting range: in measuring range of sensor
Factory setting: 0.50 m/s

0.50 m/s

Pband

Setting

Min. Speed

(basic speed only when needed)

Setting range:

|

OFF

|

→

“

Shutdown Freq.

”

(

Motor Setup) -

“

Max. Speed

”

.

Factory setting:

|

OFF

|

OFF

Min. Speed

Setting

Max. Speed

(speed limitation only when needed)

Setting range:

“

Max. Frequency

”

(

Motor Setup) -

“

Min. Speed

”

Factory setting: 50.0 Hz

50.0 Hz

Max. Speed

Setting

Manual mode

“

OFF

”

= automatic control as function of the set parameters (Factory setting)

“

ON

”

= automatic control without function, speed setting in menu

“

Speed manual

”

OFF

Manual mode

Setting

Speed Manual mode

Manual speed setting without in

ﬂ

uence by the external signal.

Activation by menu

“

Manual mode

”

or external contact at digital input (

IO Setup).

Setting range: 0...

“

Max. Frequency

”

(

Motor Setup)

Factory setting: 50.0 Hz
For information about deactivated regulation the adjusted value for manual speed is
indicated alternating with the actual value.

50.0 Hz

Speed man.

Operating Instructions

Fcontrol

–

model series FXDM25/32AM

Programming

L-BAL-E212-GB 1451 Index 003

Part.-No.

52/123

«
...
50
51
52
53
54
...
»

Summary of Contents for FXD32AM




























































































































Reviews:

No comments

Related manuals for FXD32AM

Brand: Samsung Pages: 24

Super-writemaster SH-S203N

Brand: Samsung Pages: 2

Brand: Samsung Pages: 32

SH-M522C - CD-RW / DVD-ROM Combo Drive

Brand: Samsung Pages: 27

SE-S084B - DVD RW / DVD-RAM Drive

Brand: Samsung Pages: 2

Brand: Samsung Pages: 19

Brand: Samsung Pages: 2

Brand: Kanguru Pages: 2

Brand: Kanguru Pages: 2

Compax3 Fluid T40

Brand: Parker Pages: 398

Brand: Magnetek Pages: 119

Brand: YASKAWA Pages: 114

Brand: Minarik Pages: 3

Brand: Penta KB Power Pages: 24

DVR 115D - DVD±RW Drive - IDE

Brand: Pioneer Pages: 2

DVR 116D - DVD±RW Drive - IDE

Brand: Pioneer Pages: 4

DVR 115D - DVD±RW Drive - IDE

Brand: Pioneer Pages: 5

Brand: Pioneer Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands