ZIEHL-ABEGG FXD32AM Operating Instructions Manual Download Page 40

Page: 40 / 123

9.2.6

For mode

2.03

Relay output for temperature monitoring

If the set value for the

“

minimum alarm

”

is not reached or the set value for the

“

maximum alarm

”

exceeded, a message is generated via the alarm symbol in the display. In addition,

„

Lmt E1 min

“

displayed alternately with the actual value for the minimum alarm and Lmt E1 max for the

„

Maximum

alarm

“

. An external message follows via the factory-assigned

“

”

relay. (IO Setup: K1 function =

Setting

Alarm Minimum

Setting range: OFF / -49.9...150.0

Factory setting: 0.0

0.0

Alarm Minimum

Setting

Alarm Maximum

Setting range: OFF / -49.9...150.0

Factory setting: 40.0

40.0

Alarm Maximum

Info

Example for display if falling below setting

“

Alarm Minimum

”

alternating to the actual

value display.
Relay

“

”

disengages (if not inverted).

Lmt E1 min

Info

Example for display if exceeding setting

“

Alarm Maximum

”

alternating to the actual

value display
Relay

“

”

disengages (if not inverted).

Lmt E1 max.

Operating Instructions

Fcontrol

–

model series FXDM25/32AM

Programming

L-BAL-E212-GB 1451 Index 003

Part.-No.

40/123

Summary of Contents for FXD32AM




























































































































Search results

Summary of Contents for FXD32AM

Reviews:

Related manuals for FXD32AM

Brands by name

Popular brands

ZIEHL-ABEGG FXD32AM, Operating Instructions Manual

Search results

Summary of Contents for FXD32AM

Reviews:

Related manuals for FXD32AM

Brands by name

Popular brands