background image

 

System of treatment of exhaust gases - setting 
The regeneration of the diesel particulate filter in case of increased temperature of exhaust gases is 
performed at higher engine load. The system of regeneration of the diesel particulate filter DPF can be 
controlled through the menu of the engine setting on the instrument panel. The regeneration can be 
controlled in two modes. The mode of automatic regeneration of the diesel particulate filter and inhibition of 
regeneration of the DPF filter (for safety reasons only). 

S15N020

 

 

Enter the menu of the engine setting by long pressing the button (A) on the instrument panel. The service 
menu screen (b) is displayed. To enter the engine setting (c), choose the corresponding tab using the 
buttons (B) and (C) and confirm it by longer pressing the button (A). The following items are displayed on the 
screen: 
 
- Automatic regeneration of the diesel particulate filter - DPF Auto 
- Inhibition of regeneration of the diesel particulate filter - DPF Inhibit 

Note: Setting of individual modes is described in Chapter System of Treatment of Exhaust Gases. 
 
 
Instrument panel - warning 
Replenish fuel 

Add urea 
When the level of the urea tank content drops, the prompt for the addition of urea and the amount of urea in 
the tank in percentage of the tank volume are shortly displayed on the display. 

When the fuel signal lamp (orange) is lit up, the prompt to 
refill the fuel appears in the display for about 3 seconds. If 
the fuel is not refilled, the prompt always appears in the 
display when the key is moved from the position ´0´ to the 
position ´I´ for about 3 seconds. The fuel signal lamp is 
permanently on. 

F15N012

 

 

 
Note: More information in chapter System of Additional 
Treatment of Exhaust Gases. 

F15N021

 

INSTRUMENT PANEL

63

Summary of Contents for Forterra CL 100







































































































































































































Reviews: