Zetor Forterra CL 100 Operator'S Manual Download

Page: 182 / 198

Main tractor's parameters (mm)

Tractor type

note

Tyre

dimensions

Front

14,9R24

Rear

580/70R38

Outline length with hitches with the front

three-point hitch lowered

4885

without ballast weights

Outline length with hitches without the

front three-point hitch

4340

without ballast weights

Width over the rear fenders

2164

Height to the exhaust outlet

2856

Tractor height to the upper cab edge

2870

Inner height under the front axle support

520

Height of the mouth of the stage hitch in

the top position (mouth centre)

1005

Wheel base

2490

MAIN TECHNICAL PARAMETERS

181

Summary of Contents for Forterra CL 100







































































































































































































Search results

Summary of Contents for Forterra CL 100

Reviews:

Related manuals for Forterra CL 100

Brands by name

Popular brands

Zetor Forterra CL 100, Operator'S Manual

Search results

Summary of Contents for Forterra CL 100

Reviews:

Related manuals for Forterra CL 100

Brands by name

Popular brands