manualshive.com logo in svg

Zetor Forterra CL 100, Operator'S Manual

Share
Download
Zetor Forterra CL 100 Operator'S Manual Download Page 28

 

Tractor user must be properly acquainted with recommended operating and safety rules for 

safe tractor operation in advance. It is too late to do it within operation! 

 

 

Safety cabin

 

Opening the door from the outside

 

Opening the door from the inside

 

 

Use the left side of the tractor for getting on 

and getting off the tractor. 

Use three-stage climbing irons and hold the bars 
when getting on and getting off the tractor. 

Pay increased attention in the area of gear shifting 

lever and manual throttle lever.

 

Safety cabin is equipped with toned glass. 

F11N039

 

 

Door can be opened from the outside by pressing 

a button. Left door can be locked. 

F_02_11

 

 

1. Lever for opening the door from the inside 

2. Lever for opening the door from the inside 

The door is held by a gas strut with a full opening. 

Driving with open door is not recommended for their 

possible damage. 

 It is forbidden driving with open door due to its 

possible damage.

 

F23

 

 

ACQUAINTANCE WITH TRACTOR

27

Summary of Contents for Forterra CL 100







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands