Z3 Technology FSDI-DCK-10 User Manual Download Page 3

Page: 3 / 75

FSDI-DCK-10 User Instructions

DOC-USR-0313-01

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

TABLE OF CONTENTS

1.0 GENERAL DESCRIPTION

.................................................................................................

2.0 FEATURES

................................................................................................................

2.1 Supported Resolutions

...............................................................................................

3.0 PACKAGE OPTIONS

......................................................................................................

4.0 OPERATING CONTROLS

...............................................................................................

5.0 GETTING STARTED WITH THE FSDI-DCK-10

........................................................................

5.1 Access the User Interface Using ZFinder

.........................................................................

6.0 STREAMING CONTROL

................................................................................................

6.1 Stream UDP

...........................................................................................................

6.2 Stream RTP

...........................................................................................................

6.3 Stream RTSP

..........................................................................................................

6.4 Stream RTMP

.........................................................................................................

6.5 Tuning for Latency

...................................................................................................

6.6 Stream Multiple Resolutions

........................................................................................

6.7 Record to USB

........................................................................................................

6.8 Microphone Input

....................................................................................................

6.9 Composite Pass-Through

............................................................................................

7.0 CAMERA CONTROL

....................................................................................................

7.1 Zoom

...................................................................................................................

7.2 Preview Image

........................................................................................................

7.3 Color Controls

........................................................................................................

7.4 Sony VISCA Camera Control

........................................................................................

7.5 ONVIF



Profile S

......................................................................................................

8.0 PERFORMING OTHER OPERATIONS WITH THE FSDI-DCK-10

......................................................

8.1 Save Current Settings

...............................................................................................

8.2 Advanced Settings Mode

............................................................................................

8.3 Set a Static IP Address

..............................................................................................

8.4 Upgrade Firmware

...................................................................................................

8.5 Setting a Password

...................................................................................................

8.6

Factory Reset

.........................................................................................................

9.0 DECODE OPTIONS

.....................................................................................................

9.1 PC Configuration for HD HEVC/H.265 Decode

...................................................................

9.2 ZEUS



SME-01 Decode

...............................................................................................

10.0 SUMMARY OF OPTIONS

..............................................................................................

10.1 The System Setup Tab

.............................................................................................

Summary of Contents for FSDI-DCK-10












































































Search results

Summary of Contents for FSDI-DCK-10

Reviews:

Related manuals for FSDI-DCK-10

Brands by name

Popular brands

Z3 Technology FSDI-DCK-10, User Manual

Search results

Summary of Contents for FSDI-DCK-10

Reviews:

Related manuals for FSDI-DCK-10

Brands by name

Popular brands