Z3 Technology FSDI-DCK-10 User Manual Download Page 8

Page: 8 / 75

FSDI-DCK-10 User Instructions

DOC-USR-0313-01

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

2.0

FEATURES

▪

HEVC/H.265 encode and stream up to 1080p at 60 fps

▪

H.264 encode and stream up to 1080p at 60 fps

▪

Encode modes of operation: HEVC/H.265, H.264 and MJPEG

▪

Low bandwidth, low latency video encoding

▪

Simultaneously output two different resolutions from a single video source

▪

Remote camera control via HTTP-based interface or pass VISCA camera control commands over IP

▪

Inputs: powered line audio

▪

Outputs: composite

▪

Additional Interfaces include Gigabit Ethernet, USB 2.0, Micro SD Card and RS-232 Serial

▪

RS485, alarm input and output interfaces available internally

▪

Supports streaming in MPEG-2 TS (UDP), RTP, RTSP, RTMP* and TSRTP

▪

Supports unicast and multicast streaming

▪

Compatible with CDN’s including Wowza Streaming Engine™

*, YouTube Live* and Facebook Live*

▪

Record a compressed .ts file to a USB storage device

▪

Easily mounts to tripods or mounting brackets (1/4 20 UNC screw hole on bottom of unit)

▪

ONVIF



profile S compliant

▪

Compatible with the ZEUS



Z3-SME-01 H.264 decoder* and Z3-HE265-DEC H.265 decoder (also

available from Z3 Technology)

▪

HTTP-based configuration software for user-friendly configuration, control and update

▪

RS-232 serial port for technical configuration and control

▪

Supports Power over Ethernet (PoE) when present

▪

Operating Temp: -5 to 70 degrees C at 20-80% relative humidity (non-condensing) with proper
thermal solution

▪

Storage Temp: -10 to 75 degrees C at 20-80% relative humidity (non-condensing)

▪

Measurements: 58 x 58 mm

▪

Weight: 87.9g

2.1

Supported Resolutions

Follow input (1080p60, 1080p59.94, 1080p50)

Resize down to 1080p, 720p and 480p

The FSDI-DCK-10 supports simultaneous output of up to three streams encoded at different resolutions,

Summary of Contents for FSDI-DCK-10












































































Search results

Summary of Contents for FSDI-DCK-10

Reviews:

Related manuals for FSDI-DCK-10

Brands by name

Popular brands

Z3 Technology FSDI-DCK-10, User Manual

Search results

Summary of Contents for FSDI-DCK-10

Reviews:

Related manuals for FSDI-DCK-10

Brands by name

Popular brands