Z3 Technology FSDI-DCK-10 User Manual Download Page 55

Page: 55 / 75

FSDI-DCK-10 User Instructions

DOC-USR-0313-01

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

Advanced
Settings

Checked

Unchecked

Check this box for advanced encode settings to
appear on the channel tab.

Display Setup

Resolution

AUTO

NTSC

PAL

Selects the desired resolution for Composite pass-
through output.

Set Display
Button

Click once the desired selection is made in the
Resolution dropdown menu to make real time
changes.

Device Management

Set Device Name
Button

Sets a custom name for the camera to appear in
the user interface.

New device

Name

Text box to enter desired device name.

Set Password
Button

Sets a password to limit access to the user
interface.

New password

Text box to enter new password.

Password again

Text box to re-enter new password.

Must match previous field.

Set SNTP Button

Click this button to access Simple Network Time
Protocol (SNTP) configuration options.

Enable SNTP

True

False

Sets whether Simple Network Time Protocol (SNTP)
is enabled.

Time Zone

America/Chicago

Allows for selection of desired time zone.

SNTP Servers

(128.138.141.172)

Address of desired server for SNTP.

Update device
firmware Button

Access the Software Updater to update the
firmware on your device. An image file of the
desired firmware is needed.

Download device
logs Button

Extract a set of diagnostic logs that can be
provided to Z3 in the event of an issue to be

Summary of Contents for FSDI-DCK-10












































































Search results

Summary of Contents for FSDI-DCK-10

Reviews:

Related manuals for FSDI-DCK-10

Brands by name

Popular brands

Z3 Technology FSDI-DCK-10, User Manual

Search results

Summary of Contents for FSDI-DCK-10

Reviews:

Related manuals for FSDI-DCK-10

Brands by name

Popular brands