Z3 Technology FSDI-DCK-10 User Manual Download Page 9 | Manualshive

Page: 9 / 75

background image

FSDI-DCK-10 User Instructions

DOC-USR-0313-01

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

9

frame rates and bitrates. Supported stream resolutions are:

1080p (2MP), 1280x1024, 720p (1MP), 480p, 576p, 1024x576, 704x576, 640x480, 640x360, 420x380,
352x576, 352x288, 352x240, 320x240, and 320x180

In addition to scaling the resolution, the camera is also capable of scaling down the frame rate to save
bandwidth. Each channel can select from full frame rate, half frame rate, quarter or sixth frame rate.
For example, it is possible to configure a primary stream of 1920x1080 at 60 fps simultaneously with a
secondary stream at 480p at 10 fps.

The maximum performance for two channels is two 1080p60 streams.

3.0

PACKAGE OPTIONS

Figure 2 FSDI-DCK-10 Package Options

*NOTE:

additional cables may be required to connect your secondary camera. Contact Sales for more

information about available cables and compatible cameras.

FSDI PCB Assembly

MCX to Flex I/O Connector

KEL Ribbon Cable

12V 2.5Amp AC Adapter

Serial Cable

Gender Changer

MMCX to BNC Conncector

«
...
7
8
9
10
11
...
»

Summary of Contents for FSDI-DCK-10












































































Reviews:

No comments

Related manuals for FSDI-DCK-10

Brand: Eco Drive Pages: 138

Vertex VCE6-HFC-4C

Brand: Spirent Pages: 8

Brand: Karma Pages: 2

Brand: M-system Pages: 5

Solar station S

Brand: meibes Pages: 21

Brand: PanelClaw Pages: 19

Brand: Dometic Pages: 288

Brand: Mitsubishi Pages: 12

Brand: Littfinski Daten Technik Pages: 2

Brand: TC Communications Pages: 31

DA1-34072FB-B20C

Brand: Eaton Pages: 16

Brand: Uhlenbrock Elektronik Pages: 4

Brand: AV Access Pages: 20

Brand: Partilink Pages: 30

Brand: Planet Pages: 28

Brand: AUTLED Pages: 2

Brand: National Instruments Pages: 54

CTRLink EIMK-100T/FT

Brand: Contemporary Controls Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands