Z3 Technology FSDI-DCK-10 User Manual Download Page 50

Page: 50 / 75

FSDI-DCK-10 User Instructions

DOC-USR-0313-01

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

8.6

Factory Reset

The FSDI-DCK-10 can be reset to its original factory settings using the pinhole reset on the lower right of the
I/O PCB of the unit.

Figure 54 Pinhole Reset

(1)

Allow the FSDI-DCK-10 to boot completely.

(2)

Press and hold pinhole reset switch until status light flashes yellow

(3)

Power cycle device. Once the boot sequence has completed the FSDI-DCK-10 will return to its
original factory settings.

9.0

DECODE OPTIONS

9.1

PC Configuration for HD HEVC/H.265 Decode

Due to the advanced processing needed to support HEVC/H.265 decoding at HD resolutions, a PC must
meet the following requirements:

▪

Nvidia GEForce GTX960 (desktop) or GTX960M (laptop) graphics card

▪

LAV Filters

version 0.63 or higher

▪

VLC media player

version 2.2.4 or higher

LAV Filters is an open source program that allows playback of video and audio on a PC without installation of

additional codecs and can be downloaded for free online.

VLC is an open source media player from the VideoLAN organization that can be downloaded for free online.

Summary of Contents for FSDI-DCK-10












































































Search results

Summary of Contents for FSDI-DCK-10

Reviews:

Related manuals for FSDI-DCK-10

Brands by name

Popular brands

Z3 Technology FSDI-DCK-10, User Manual

Search results

Summary of Contents for FSDI-DCK-10

Reviews:

Related manuals for FSDI-DCK-10

Brands by name

Popular brands