Z3 Technology FSDI-DCK-10 User Manual Download Page 11 | Manualshive

Page: 11 / 75

background image

FSDI-DCK-10 User Instructions

DOC-USR-0313-01

______________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

11

5.0

GETTING STARTED WITH THE FSDI-DCK-10

WARNING: Use ONLY FCB-EV7520 or compatible camera with the FSDI-DCK-10. Using an incompatible
camera may permanently damage the camera and the FSDI-DCK-10.

Figure 4 Camera Compatibility Warning

Figure 5 FSDI-DCK-10 Physical Block Diagram (Cameras Not Included)

(1)

Once received, the FSDI-DCK-10 assembly will need to be connected to a SDI camera ( or the Sony
FCB-EV7520 HD camera block) and the secondary camera with Composite Out. The Interface Front
End PCB of the FSDI-DCK-10 assembly (see Figure 7) has SDI input or 30-pin KEL connectors that
allow a flexible ribbon cable to be used to connect the encoder assembly to an identical connector
on the Sony FCB-EV7250. The Composite Out secondary camera is connected to the FSDI-DCK-10
assembly via the MMCX or Flex I/O Connector (see Figure 6 8). The KEL cable (ordering part number:

SDI Camera

BNC

M

M

CX

M

M

CX

BNC

«
...
9
10
11
12
13
...
»

Summary of Contents for FSDI-DCK-10












































































Reviews:

No comments

Related manuals for FSDI-DCK-10

Brand: ICP DAS USA Pages: 7

Brand: Parker Pages: 99

Brand: TANDBERG Pages: 384

E5714 DSNG Voyager

Brand: TANDBERG Pages: 314

ACS 600 MultiDrive

Brand: ABB Pages: 94

Rapid Shutdown Box-Duo

Brand: Fronius Pages: 60

Brand: Patton electronics Pages: 16

Brand: Alca Power Pages: 8

Brand: Mitsubishi Pages: 96

Brand: V-TAC Pages: 42

Brand: V-TAC Pages: 55

Brand: V-TAC Pages: 36

Brand: Whisper Power Pages: 41

Brand: SEO Electronics Pages: 4

DIYSolar OFF-GRID

Brand: ECO POWER Pages: 12

Brand: BOLIY Pages: 26

Brand: Asante Pages: 16

Freedom SW 815-2012

Brand: Xantrex Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands