342
JOHNSON CONTROLS
FORM 201.21-NM3 (616)
PRINTER WIRING
Printer Cables
Printer cables should be shielded coaxial, #18AWG,
stranded wire cables, not to exceed 50’ in length. On
long cable runs or whenever permanent installation is
required, the shield of the coax should be tied to the
chassis ground at the chiller only, not at the printer.
Printer Setup
The following information may be useful for quick set up
of a printer. Specific printer manuals should be utilized,
if problems occur, since functions often change as new
versions of printers are introduced with enhancements
requiring control code, signal programming, and wiring
changes.
OKIDATA 184:
Control Board Switch settings:
SW1 – on: Unslashed 0
2 – off: Unslashed 0
3 – off: Unslashed 0
4 – off: Form Length 11 in.
5 – on: Form Length 11 in.
6 – off: Auto Line feed off
7 – on: 8 bit data
8 – off: Enable front panel
With SUPER SPEED Serial Board:
SW1-1 – on: Odd or even parity
1-2 – on: No parity
1-3 – on: 8 bit data
1-4 – on: Protocol ready/busy
1-5 – on: Test select
1-6 – on: Print mode
1-7 – off: SDD(-) pin 11
1-8 – on: SDD(-) pin 11
2-1 – on: 1200 baud
2-2 – on: 1200 baud
2-3 – off: 1200 baud
2-4 – off: DSR active
2-5 – on: Buffer threshold 32 bytes
2-6 – on: Busy signal 200ms
2-7 – on: DTR space after power on
2-8 – not used
With SUPER SPEED Serial Board:
SW1 – off: (-) Low when busy
2 – off: 1200 baud
3 – off: 1200 baud
4 – on: 1200 baud
5 – not used
6 – off: no parity
7 – off: Pin 20 & pin 11 act as busy line
WEIGH-TRONIX IMP 24 MODEL 2600:
SW1 – off: 1200 baud
2 – on: 1200 baud
SEIKO:
DipSW1-1 – off: Input -Serial
1-2 – on: Printing speed high
1-3 – on: Auto loading - on
1-4 – off: Auto LF - off
1-5 – on: Setting Command - Enable
1-6 – off: Printing density - 100%
1-7 – on: Printing density - 100%
1-8 – on: Printing density - 100%
DipSW2-1 – on: Printing Columns - 40
2-2 – on: User Font Back-up - on
2-3 – on: Character Select - normal
2-4 – off: Zero - slash
2-5 – on: International character set-
American
2-6 – on: International character set -
American
2-7 – on: International character set -
American
2-8 – off: International character set –
American
DipSW3-1 – on: Data length - bits
3-2 – on: Parity Setting - no
3-3 – on: Parity condition - odd
3-4 – on: Busy control – H/W busy
3-5 – on: Baud rate select - 1200
3-6 – off: Baud rate select - 1200
3-7 – on: Baud rate select - 1200
3-8 – off: Baud rate select - 1200
MAINTENANCE
Summary of Contents for YCAV0267E
