YOKOGAWA AQ6380 User Manual Download Page 94

Page: 94 / 102

6-3

IM AQ6380-02EN

Specifications

App

Index

Function

Item

Function

Measurement

CW light, pulse light (peak hold, external trigger, gate sampling)

Sweep settings

Single, repeat, AUTO (automatically sets measuring conditions), inter-line

marker sweep, 0 nm span sweep

Measurement

condition settings

Center wavelength, span, wavelength sampling points, wavelength

resolution, measurement sensitivity (TRAD/RAPID mode), high dynamic

range mode, average times (1 to 999), smoothing, air/vacuum wavelength

Other

Sweep status output, analog output

Display

Vertical scale

Level scale (0.1 to 10 dB/div, linear), level subscale (0.1 to 10 dB/div, linear),

reference level, divisions (8, 10), percentage (%), power spectral density (dB/

nm), noise mask

Horizontal scale

Wavelength (nm), frequency (THz), trace zoom in/out

Display items

Measurement conditions, traces, data table, labels

Trace

7 independent traces, MAX/MIN hold, trace-to-trace calculation,

normalization, rolling average (2 to 100), curve fitting, peak curve fitting,

marker curve fitting, power spectral density (POWER/NBW), trace copy,

trace clear, trace write/fix setting, trace show/hide setting

Marker

Delta markers (up to 1024 markers), power spectral density markers, power

integral markers, line markers

Peak search (single/multi), bottom search (single/multi), auto search (ON/

OFF), search between wavelength line markers, search within zoom area

Data analysis

Spectral width analysis (Threshold, Envelope, RMS, Peak-RMS, Notch),

WDM (OSNR) analysis, EDFA-NF analysis, filter analysis (peak/bottom),

WDM filter analysis (peak/bottom), DFB-LD analysis, FP-LD analysis, LED

analysis, SMSR analysis, power analysis, auto analysis ON/OFF, analysis

between wavelength line markers, analysis in the zoom area

Applications

WDM test, DFB-LD test, LED test, FP-LD test, fiber end face test, application

management (add/remove)

Other

Optical axis

adjustment

Auto alignment adjustment using the built-in light source

Calibration

Auto wavelength calibration using the built-in light source, wavelength

calibration using an external light source, wavelength resolution calibration

using an external light source

6.1 Signal Input Section

Summary of Contents for AQ6380







































































































Search results

Summary of Contents for AQ6380

Reviews:

Related manuals for AQ6380

Brands by name

Popular brands

YOKOGAWA AQ6380, User Manual

Search results

Summary of Contents for AQ6380

Reviews:

Related manuals for AQ6380

Brands by name

Popular brands