YOKOGAWA AQ6380 User Manual Download Page 38 | Manualshive

Page: 38 / 102

background image

Preparing for Measurement

3-7

IM AQ6380-02EN

1

2

3

4

5

6

App

Index

3.2 Connecting the Device

Connecting a USB Storage Device

Supported USB Storage Devices

The instrument supports USB memory (USB card adapters).
You cannot use a USB storage device not recognized by the instrument. If the USB storage
device’s drive is partitioned, only the primary partition is recognized. If there are two or more USB
storage devices, only the first connected device is recognized.
If you restart the instrument, it the USB storage devices that were connected will still be recognized.

Connections

Connect the USB storage device to the USB connector on the front panel of the instrument.

USB connector

Removing

See section 8.1 in IM AQ6380-01EN. (You will use the Remove USB Storage soft key.)

CAUTION

Do not remove the USB storage device or turn the power OFF while the USB storage device
access indicator is blinking. This can damage the data on the device or the device itself.

French

ATTENTION

Ne retirez pas le dispositif de stockage USB et ne coupez pas l’alimentation lorsque le voyant
d’accès au dispositif de stockage USB clignote. Cela risquerait d’endommager le dispositif ou
les données se trouvant sur ce dernier.

Connecting with Other Devices

The GP-IB or Ethernet interface can be used to connect external devices to this instrument. For
details, see the Remote Control User’s Manual, IM AQ6380-17EN.

Note

Before connecting a GP-IB instrument, such as an external computer, or a LCD monitor or other display to

the instrument, check the wiring, and be sure to turn OFF the power to the instrument and the instruments

to be connected first.

Leaving the power ON while making connections can damage the equipment.

«
...
36
37
38
39
40
...
»

Summary of Contents for AQ6380







































































































Reviews:

No comments

Related manuals for AQ6380

Brand: C-LOGIC Pages: 2

Brand: Medeli Pages: 14

Brand: M-system Pages: 18

YPP-100 Light Piano

Brand: Yamaha Pages: 54

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 56

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 32

Brand: Energic Plus Pages: 12

Brand: Vectronics Pages: 4

Brand: YATO Pages: 36

Brand: TSI Instruments Pages: 4

Brand: GREISINGER Pages: 20

Brand: Supertech agroline Pages: 10

Brand: A&D Pages: 2

Brand: Major tech Pages: 20

Proline Promag W 400

Brand: Endress+Hauser Pages: 64

Brand: National Instruments Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands