manualshive.com logo in svg

YASKAWA CIMR-P7U-2011-107, Programming Manual

The YASKAWA CIMR-P7U-2011-107 is a technologically advanced programmable device with a comprehensive Programming Manual. This manual provides detailed instructions and guidance for users to leverage the product's capabilities effortlessly. Download the free manual from manualshive.com and unlock the full potential of your YASKAWA CIMR-P7U-2011-107 for optimal performance.

Share
Download
background image

YASKAWA

 TM.iQp.02 iQpump Drive Programming Manual

 161

Pre-Charge with Thrust Bearing Function Both Enabled. 

<0032>

When both Pre-Charge and Thrust Bearing modes are enabled, the system will function as follows: Upon receiving a run command, the 

drive will ramp up to the Thrust Bearing Frequency (P4-05) using the Thrust Bearing Acceleration Time (P4-04). After reaching the 

Thrust Bearing Frequency (P4-05), the Pre-Charge becomes active and P4-05 becomes the new minimum frequency. The drive will ramp 

up to the Pre-Charge Frequency (P4-02) and will remain at this frequency until the Pre-Charge has been completed. This can occur when 

the P4-03 time has expired, P4-01 level has been reached, or the Low Water digital input has been deactivated.

If the drive is to stop at any time after the Thrust Bearing Frequency has been reached, the drive will ramp down to the P4-05 frequency 

at the rate programmed in Deceleration Time (C1-02). This condition can occur due to loss of run command, auto mode, or drive is in the 

sleep mode. The drive will then ramp down from a frequency (P4-05) to 0 using Deceleration Time programmed in P4-06. The Thrust 

Bearing Acceleration is active when working from sleep while the Pre-Charge is not.

The Pre-Charge Frequency (P4-02) should be set to a value greater than the Thrust Bearing Frequency (P4-05). If the Pre-Charge 

Frequency (P4-02) is less than the Thrust Bearing Frequency (P4-05), the drive will internally use a Pre-Charge Frequency equal to the 

P4-05 value.

If the Pre-Charge Frequency (P4-02) is less than the Minimum Pump Frequency (P1-06), the drive will internally use a Pre-Charge 

Frequency equal to the Minimum Pump Frequency (P1-06) value.

Figure 1.124  

Figure 129  

       Run
Command

      

Output Frequency

     Pre-Charge 
Frequency P4-02

   Thrust Bearing 
Frequency P4-05

     Pre-Charge 
     Level P4-01

    

TIME

Thrust Bearing Mode and Pre-Charge Function in Auto Mode

  Standard
Accel Time
     C1-01

Thrust Bearing
    Accel Time
        P4-04

Pre-Charge
Complete

  Standard
Decel Time
      C1-02

Thrust Bearing
    Decel Time
         P4-06

Stop due to 
Sleep Mode

PI Feedback

Summary of Contents for CIMR-P7U-2011-107



















































































































































































































Reviews:

No comments

Related manuals for CIMR-P7U-2011-107

Danfoss VLT Integrated Servo Drive ISD 510 System Operating Manual preview
VLT Integrated Servo Drive ISD 510 System
Brand: Danfoss Pages: 226
Anaheim Automation DPN10601 User Manual preview
DPN10601
Brand: Anaheim Automation Pages: 52
Xinje DS5B Series Manual preview
DS5B Series
Brand: Xinje Pages: 109
lumishore SUPRA SY225 Installation And Operating Instructions Manual preview
SUPRA SY225
Brand: lumishore Pages: 7
Aquagem iSAVER Power+1100 Installation & User Manual preview
iSAVER Power+1100
Brand: Aquagem Pages: 8
Carotron C14521-000 Instruction Manual preview
C14521-000
Brand: Carotron Pages: 12
hager HXF04 H Series User Instructions preview
HXF04 H Series
Brand: hager Pages: 4
RIB KING FAST Manual preview
KING FAST
Brand: RIB Pages: 56
BLUM Flex Installation Instructions Manual preview
Flex
Brand: BLUM Pages: 20
QPS Que! Combo FireWire Installation Manual preview
Que! Combo FireWire
Brand: QPS Pages: 64
National Instruments NI MID-7654 User Manual And Specifications preview
NI MID-7654
Brand: National Instruments Pages: 32
Danfoss VLT ISD 511 Operating Manual preview
VLT ISD 511
Brand: Danfoss Pages: 156
Lenze AC Tech MCH Series Reference Manual preview
MCH Series
Brand: Lenze AC Tech Pages: 33
Teac CD-540E Installation Manual preview
CD-540E
Brand: Teac Pages: 12
Samsung TS-H492A User Manual preview
TS-H492A
Brand: Samsung Pages: 26
Unitek Bamobil D3.2 Manual preview
Bamobil D3.2
Brand: Unitek Pages: 40
JVC Everio CU-VD3U Instructions Manual preview
Everio CU-VD3U
Brand: JVC Pages: 24
JVC CU-VD10 series Instructions Manual preview
CU-VD10 series
Brand: JVC Pages: 112

Brands by name

Popular brands

Load more brands