Yamaha YZF-R1 2012 Service Manual Download Page 420

Page: 420 / 556

SIGNALING SYSTEM

8-23

EAS27290

TROUBLESHOOTING

• Any of the following fail to light: turn signal light, brake light or an indicator light.
• The horn fails to sound.

TIP

• Before troubleshooting, remove the following part(s):
1. Rider seat
2. Passenger seat
3. Fuel tank
4. Side cowlings
5. Meter assembly

→

↓

→

↓

→

↓

→

↓

Check the signaling system

The horn fails to sound.

→

↓

→

↓

1. Check the fuses.

(Main, ignition, signaling system
and turn signal light)
Refer to “CHECKING THE FUSES”
on page 8-129.

Replace the fuse(s).

2. Check the battery.

Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 8-129.

• Clean the battery terminals.
• Recharge or replace the battery.

3. Check the main switch.

Refer to “CHECKING THE
SWITCHES” on page 8-125.

Replace the main switch/immobilizer
unit.

4. Check the entire signaling system’s

wiring.
Refer to “CIRCUIT DIAGRAM” on
page 8-21.

Properly connect or repair the signal-
ing system’s wiring.

This circuit is OK.

1. Check the horn switch.

Refer to “CHECKING THE
SWITCHES” on page 8-125.

Replace the left handlebar switch.

2. Check the horn.

Refer to “CHECKING THE HORN”
on page 8-140.

Replace the horn.

Summary of Contents for YZF-R1 2012













































































































































































































































































































































































































































































































































































Search results

Summary of Contents for YZF-R1 2012

Reviews:

Related manuals for YZF-R1 2012

Brands by name

Popular brands

Yamaha YZF-R1 2012, Service Manual

Search results

Summary of Contents for YZF-R1 2012

Reviews:

Related manuals for YZF-R1 2012

Brands by name

Popular brands