THROTTLE BODIES
6-9
EAS26980
CHECKING THE INJECTORS
WARNING
EWA1TP1015
• Check the injectors in a well-ventilated area
free of combustible materials. Make sure
that there is no smoking or use of electric
tools in the vicinity of the injectors.
• Be careful when disconnecting the fuel
hoses. Any remaining pressure in the fuel
hoses may cause the fuel to spray out.
Place a container or rag under the hoses to
catch any fuel that spills. Always clean up
any spilt fuel immediately.
• Turn the main switch to “OFF” and discon-
nect the negative battery lead from the bat-
tery terminal before checking the injectors.
NOTICE
ECA1TP1019
• Always use new O-rings.
• When checking the injectors, do not allow
any foreign material to enter or adhere to
the injectors, fuel rail, or O-rings.
• Be careful not to twist or pinch the O-rings
when installing the injectors.
• If an injector is subject to strong shocks or
excessive force, replace it.
• If installing the original fuel rail and bolts,
remove the white paint marks using a
cleaning solvent. Otherwise, paint chips on
the bolt seats could prevent the bolts from
being tightened to the specified torque.
1. Check:
• Injectors
Damage/defective
→
Replace.
Refer to “FUEL INJECTION SYSTEM” on
page 7-39.
EAS1TP1041
INSTALLING THE INJECTORS
1. Install the injectors to the inlet pipe assembly.
2. Install a seal onto the end of each injector.
3. Install the inlet pipe assembly to the intake
manifold.
EAS26990
CHECKING THE THROTTLE BODIES
1. Check:
• Throttle bodies
Cracks/damage
→
Replace the throttle bod-
ies as a set.
2. Check:
• Fuel passages
Obstructions
→
Clean.
EAS1TP1043
CHECKING THE INTAKE MANIFOLD JOINTS
1. Check:
• Intake manifold joints
Cracks/damage
→
Replace.
EAS1TP1044
CHECKING THE PRESSURE REGULATOR
OPERATION
1. Check:
• Fuel pressure
▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼▼▼
a. Disconnect the fuel hose (fuel pump to fuel
hose) “1” from the fuel hose (fuel hose to fuel
filter).
WARNING
EWA1TP1017
Cover fuel hose connections with a cloth
when disconnecting them. Residual pres-
sure in the fuel lines could cause fuel to
spurt out when removing the hoses.
b. Connect the fuel pressure adapter “2” be-
tween the fuel hose (fuel pump to fuel hose)
“1” and fuel hose (fuel hose to fuel filter) “3”.
c. Connect the pressure gauge “4” to the fuel
pressure adapter “3”.
d. Connect the vacuum/pressure pump gauge
set “5” to the pressure regulator “6”.
T
R
.
.
Inlet pipe assembly bolt
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
LOCTITE®
1
Summary of Contents for XVS950CU 2014
