SHAFT DRIVE
4-99
4. Remove:
• Bearing retainer
(with the special tool “1”)
NOTICE
ECA14330
The bearing retainer has left-hand threads.
To loosen the bearing retainer, turn it clock-
wise.
5. Remove:
• Final drive pinion gear
WARNING
EWA13800
Always use new bearings.
NOTICE
ECA14340
The final drive pinion gear should only be re-
moved if ring gear replacement is necessary.
TIP
Lightly tap on the end of the final drive pinion
gear with a soft hammer.
EAS2S31031
REMOVING AND INSTALLING THE
BEARING
1. Check:
• Bearing
Damage
→
Replace.
2. Remove:
• Dowel pin “1”
• Bearing “2”
▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼▼▼
a. Heat the final drive case to approximately
150 °C (302 °F).
b. Remove the bearing with an appropriately
shaped punch.
c. Remove the inner race from the final drive
pinion gear.
TIP
The removal of the final drive pinion gear bear-
ing is a difficult procedure and is rarely neces-
sary.
▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲▲▲
3. Install:
• Bearing
• Dowel pin
▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼ ▼▼▼
▼
▼▼▼
a. Heat the final drive case to approximately
150 °C (302 °F).
b. Install the bearing with a socket or appropri-
ate tool that matches the diameter of the out-
er race.
c. Install the inner race onto the final drive pin-
ion gear.
▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲ ▲▲▲
▲
▲▲▲
EAS2S31029
ASSEMBLING THE FINAL DRIVE
ASSEMBLY
1. Install:
• Final drive case stud bolts
TIP
• Apply LOCTITE® to the threads of the final
drive case stud bolts.
Bearing retainer wrench
90890-04159
Pinion bearing retainer & remov-
er
YM-04159
1
1
1
2
New
Summary of Contents for Vmax VMX17C 2009
