ABS (ANTI-LOCK BRAKE SYSTEM)
4-58
EAS2S31026
INSTALLING THE HYDRAULIC UNIT
ASSEMBLY
1. Install:
• Hydraulic unit assembly box
• Hydraulic unit assembly
TIP
Do not allow any foreign materials to enter the
hydraulic unit assembly or the brake hoses
when installing the hydraulic unit assembly.
NOTICE
ECA2S31026
Do not remove the rubber plugs or bolts
(M10
×
1.0) installed in the flare nut holes be-
fore installing the hydraulic unit assembly.
2. Remove:
• Rubber plugs or bolts (M10
×
1.0)
3. Install:
• Brake hoses
• Brake hose holder “1”
TIP
• Temporarily tighten the brake hose flare nuts
and brake hose holder bolt.
• Insert the tab “a” on the brake hose holder into
the slot “b” in the battery box bracket.
4. Tighten:
• Brake hose flare nuts
• Brake hose holder bolt
NOTICE
ECA2S31027
If the brake hose flare nut does not turn eas-
ily, replace the hydraulic unit assembly,
brake hoses, and related parts as a set.
TIP
• First tighten the brake hose flare nut, then the
brake hose holder bolt.
• Do not bend the pipe section of the brake hose
when tightening the brake hose flare nuts.
• When tightening the brake hose flare nuts,
make sure that the brake pipes are positioned
at the angles shown in the illustration.
5. Connect:
• ABS ECU coupler “1”
TIP
Push the coupler ejection slider down until a
click is heard, making sure that is installed se-
curely.
T
R
.
.
Hydraulic unit assembly box bolt
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
a
b
1
T
R
.
.
Brake hose flare nut
16 Nm (1.6 m·kgf, 11 ft·lbf)
Brake hose holder bolt
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
3–7˚
30–34˚
54–58˚
89–93˚
Summary of Contents for Vmax VMX17C 2009
