background image

MOUNTING INSTRUCTIONS 

Figure 3 

Figure 1 

Space Approx. 
2" apart. 

WARNING:  

"Mounting clamps 
backwards will cause 
damage to your tank." 

 

Figure 2 

  MEB8929    1-11-11

 

Glass cleansing agents will cause severe damage 

to your windshield, and will void your warranty. 

 

 

NOTE: 

 At certain times of the day the Sunlight can reflect 

off the curvature of a windshield and cause extreme heat 
build-up on motorcycle instruments and instrument panel. 
Take care when parking. Park facing the sun, place an opaque 
object over the instruments or adjust the windshield to avoid 
reflections. 

IMPORTANT CARE AND CLEANING INSTRUCTIONS 

Memphis Shades Windshields and Lowers are made of 
Lucite® acrylic, and will last for years with proper care. 
Clean your windshield with plenty of soapy water — mild 
dishwashing liquid is best — and a soft cotton cloth. Use your 
bare hand to feel and dislodge bugs, or cover with a wet soapy 
towel and let it soak. Don't use paper towels and don't scrape 
with anything. Small scratches can be removed with NOVUS 
# 2. 
 
NEVER use any glass cleaning products, petroleum based 
chemicals, or cleaning agents with ammonia, bleach or any 
other harsh chemicals. This includes (but not limited to) 
RainX, brake fluid, acetone, paint thinner, benzene and 
gasoline. "If it hurts your nose, it will hurt the plastic." 

No additional tools required for this kit. 
 
1. 

Cover gas tank and front fender with a towel to avoid 

damage during installation. 

2. Install the windshield mounting plates onto the windshield, 
using the bolts that are pre-assembled on the mounting plates. 
The Santoprene grommets should be inserted through the 
holes in the windshield so that the flat round part of the grom-
met lies flat on each side of the plastic. 

Tabs point in towards 

the headlight

(see figure 1 ) 

 3. Loosely install the four Fork Clamps on the forks, approxi-
mately 2" apart. (see figure 2) 
4. Start with Fork Clamp Bushing adjusted to rear of  slot (see 
figure 4) Then adjust as needed and check for clearance. (See 
warning above.) 
5. Slip the windshield mounting plates and windshield onto 
the fork clamps, (see figure 3 and 5) and secure the left and 
right side locking mechanism 
6. Adjust the height, angle and alignment of the windshield 
and tighten 

ALL 

bolts. 

 

Note: This is a detachable windshield, ALWAYS make 
sure the Locking Mechanism is Fully Engaged after in-
stalling the windshield!  (see figure 5)

 

Start with Fork Clamp Bushing ad-
justed to rear of  slot. Then adjust as 
needed and check for clearance. 

(See 

above "Read and Follow Directions 
Warning.") 

Fig. 4 

Bushings 

Throttle side, 
front of bike 

INCORRECT  

CORRECT  

Read and follow these directions carefully. 

During installation, make sure that the windshield and hard-
ware do not interfere with any cables or wiring when the forks 
are turned all the way in either direction. Also make sure, 
through the full range of adjustment, that the windshield and 
hardware do not hit the tank. 

 

This is a detachable windshield, ALWAYS make sure the 
Locking Mechanism is Fully Engaged after installing the 
windshield! 

The improper installation of this kit and related compo-
nents could result in serious injury or death.  

 2320-0076 SPORTSHIELD DETACHABLE MOUNTING KIT 

06-07 DYNA WIDE GLIDE, BLACK

 

Reviews: